Skip to main content

sen.06 - Parametric modelling

  • Module code sen.06
  • Software
    • SCIA Engineer
  • Included in editions
    • Professional,
    • Expert,
    • Ultimate
  • Category Modelling
  • License Perpetual

Highlights

  • Almost any property in a model can be expressed as a parameter: coordinates, dimensions, material classes, cross-sections, loads, etc.
  • Formulae can be used to express a parameter as a function of other parametrised properties.
  • A dialogue with defined parameters displays upon opening a parametric project. The user then fills in numerical values for the parameters. The structure is generated based on the defined numerical input.
  • In open projects, SCIA Engineer automatically regenerates the model upon a modification of a parameter. The structure is then ready to be analysed.
  • Parametrisation is also applicable to user blocks
  • Parameters allow you to optimise a structure and obtain the most economical design, minimise the load effect, or maximise/minimise any other property of the 3D model.

The Parametric modelling module (1) eliminates the need to actively adapt the model after changes to the initial design, and (2) enables general optimisation.

Application

Examples of the use of parameters in a model include:

  • Nodes, supports, and loads whose location are defined by parameters;
  • A cross-section of a member that is defined as a parameter;
  • Loads with parametrised magnitude.

Each parameter has a specific type assigned. For example, only parameters of type length can be assigned to distances. Types make it easier to handle units, especially when ranges must be defined for the valid values of a parameter.

The module makes it possible to also parametrise libraries. As an example, one parameter type in SCIA Engineer is Cross section - it allows the user to assign a parametric cross-section to a member. Valid values for this type of parameter are all entries in the Profile Library. To limit the number of cross-sections that are selected, user-defined sets with a limited number of cross-sections can be created in a quick and easy way.

Combined with User Blocks

User Blocks is a standard functionality in SCIA Engineer that allows for common or repeatable structural assemblies to be stored and reused in future models. Continuous beams, trusses, 2D/3D frames, etc. are examples of structures that are stored as User Blocks - these can be assigned cross-sections, supports, loads, connections and saved.

In combination with User Blocks, parametric modelling allows users to prepare parametric structures that can be inserted in any project as a sub-structure taken from the User Block Library. In this way, many types of structures are modelled much faster as one never needs to model from scratch.

Combined with Project Templates

When used in combination with the Project Template functionality of the Productivity Toolbox, the module allows users to create parametric projects with predefined geometry, material sets, loads, combinations and calculation report.

The obtained models are effectively simple programs for e.g. the calculation of continuous beams, simple frames, and other standard structures. In this way, design calculations can be performed, and documentation be prepared in a matter of minutes in the case of standardised structures.

Boolean operators with parameters

As the final geometry and status of a model is not known in advance for parametric projects, Boolean operators add flexibility to the model definition techniques. For example, loads can be defined to only act in case certain conditions are fulfilled, addition bracing can be added only if the number of spans is high enough to require it, etc.

Parametric User Blocks may contain modular elements, e.g. continuous beams and frames where the number of spans is defined by the end-user.

Summary

When well prepared, parametric modelling may effectively be used for:

  •  Analysis of projects where several variants must be prepared and evaluated.
  • Analysis of project where some level of optimisation is necessary.
  • Presentation and teaching purposes when the effect of a change in the input variables should be shown, etc.
  • Parameters enable the fast, easy and simple modification of e.g. structure dimensions, load values, assigned sections, etc.
  • A change in a parameter leads to automatic model regeneration, the newly introduced value is taken into account.

Required modules:

  • sen.00
SCIA Engineer free trial

Want to try SCIA ENGINEER yourself?

Explore how our software and services can help you optimise your work and boost your productivity. Try it for yourself with a free 30-day software trial.

Download a free 30-days full trial  

Request an offer for SCIA Engineer

Contact support for more technical information